Hi.

I have a Pcats tuner and sony RMX4S remote.

The remote does work ok, but the empeg does not react to the button presses in a sutible time period , some times taking 20secs to do a command.

Any way to speed this up?

Thanks

C.

Anyone at least confirm how yours works.

C.

Works instantaneously, or near enough.

MOST of the time, that is.

There have been reports in the past of the buttons and the stalk suffering longish delays within the first minute after powerup/resume in some situations. Dunno what the resolution was.

Cheers

Thanks.

Works fine most of the time on the tuner , but on the player is normaly slow , some times it will work o and then if i skip say 10 songs it starts to slow down.

I am thinking i might just sell the tuner as the stalk control was the reason i got , if i had know it was as flakey as it is i would not have got it.

C.

Do you have any heavy userland apps running in the background (e.g. GPSApp or Roadmapgpsapp)? These probably take up buffer space so after skipping 10 songs the empeg won't respond to commands until it refills it's buffers.

Only have empacman running as a init script.

I do have an additional buffer section in my ini file.

C.

Try removing those temporarily and see if it solves your tuner stalk delay problem.

Will Do.

Thanks

C.

Back on this again.

Tried both my players with just V2 on them and both have slow down periods when responding to button presses.

C.

Tried both my players with just V2 on them and both have slow down periods when responding to button presses.

Have a look at this thread...

Not sure that that realy helps me much as mine is empeg tuner remote.

I do have 2 stereo's but have only had the battery warning once.

C.

Not sure that that realy helps me much as mine is empeg tuner remote.

So is Tod's. Read carefully, we're reporting the exact same problem.

What is a soundgate then?

Also found this thread
http://empeg.comms.net/php/showflat.php?Cat=&Board=empeg_general&Number=158392&page=&view=&sb=&o=&vc=1

Other things...

I also get the same style of slow response from the http interface on just the player so the whole stalk thing might be a bit of a fish.

I also get the same thing from your face program.

Sort of not related but do you have a port of your face progam for pocket PC ?

Thanks

C.

I also get the same thing from your face program.

Ah, that's very telling. It means something fishy is going on with your player. You're right, it's got nothing to do with the stalk.

Please post your config.ini and a boot log.

No, I don't have a pocketPC version. Do pocketPCs have ethernet?

Will do.

Pocket Pc will take ethernet and 802.11* wireless cards.

If it was possible that would make the "Empeg hidden under seat" issue not a problem.

Will post the configs later.

C.

empeg-car bootstrap v1.02 20001106 ([email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!

e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux..................................... done, booting the kernel.

Linux version 2.2.17-rmk5-np17-empeg52-hijack-v340 (root@ibbm) (gcc version 2.95.3 20010315 (release)) #2 Wed Jun 18 18:40:14 EDT 2003

Processor: Intel StrongARM-1100 revision 11

NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.

empeg-car player (hardware revision 9, serial number 30102889)

Command line: mem=16m

Calibrating delay loop... 207.67 BogoMIPS

Memory: 15016k/16M available (976k code, 20k reserved, 368k data, 4k init)

Dentry hash table entries: 2048 (order 2, 16k)

Buffer cache hash table entries: 16384 (order 4, 64k)

Page cache hash table entries: 4096 (order 2, 16k)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.2

Based upon Swansea University Computer Society NET3.039

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

TCP: Hash tables configured (ehash 16384 bhash 16384)

IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)

Starting kswapd v 1.5

SA1100 serial driver version 4.27 with no serial options enabled

ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART

ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART

ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART

Signature is 206f6972 'rio '

Tuner: loopback=0, ID=-1

empeg display initialised.

empeg dsp audio initialised

empeg dsp mixer initialised

empeg dsp initialised

empeg audio-in initialised, CS4231A revision a0

empeg remote control/panel button initialised.

empeg usb initialised, PDIUSBD12 id 1012

empeg state support initialised 0089/88c1 (save to d0005c80).

empeg RDS driver initialised

empeg power-pic driver initialised (first boot)

RAM disk driver initialized: 16 RAM disks of 4096K size

empeg single channel IDE

Probing primary interface...

hda: FUJITSU MHL2300AT, ATA DISK drive

hda: FUJITSU MHL2300AT, ATA DISK drive

hda: FUJITSU MHL2300AT, ATA DISK drive

hda: FUJITSU MHL2300AT, ATA DISK drive

hda: FUJITSU MHL2300AT, ATA DISK drive

hda: FUJITSU MHL2300AT, ATA DISK drive

ide0 at 0x000-0x007,0x038 on irq 6

hda: FUJITSU MHL2300AT, 28615MB w/2048kB Cache, CHS=58140/16/63

empeg-flash driver initialized

smc chip id/revision 0x3349

smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])


SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:26:0b:49

Partition check:

hda: hda1 < hda5 hda6 > hda2 hda3 hda4

RAMDISK: ext2 filesystem found at block 0

RAMDISK: Loading 320 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\done.

EXT2-fs warning: checktime reached, running e2fsck is recommended

VFS: Mounted root (ext2 filesystem).

empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.

change_root: old root has d_count=1

Trying to unmount old root ... okay

Freeing unused kernel memory: 4k init
empeg-preinit starting...
empeg-preinit complete
empeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Tried to mount /dev/hdc4 but got error 6
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
Hijack: intercepting config.ini


hijack: removed menu entry: "Tuner RDS Control"

hijack: removed menu entry: "Serial Port Assignment"

khttpd: listening on port 80

kftpd: listening on port 21

player.cpp : 385:empeg-car 2.00 2003/04/01.
empacman running as pid 15
Mounting /programs0... mount: can't find /programs0
in /etc/fstab or /etc/mtab
Prolux 4 empeg car - 2.1434 Mar 26 2003
Vcb: 0x4086d000

[Options]
Name=Robs RioCar
[User Info]
Email=******************
Phone=****************
Name=******************
[Network]
Gateway=0.0.0.0
Netmask=255.0.0.0
IPAddress=10.0.0.79
DHCP=1
[power]
off_timeout=20000
[display]
play_count=1
visual_names=0
caching=0
[synchronise]
seq_num=119
[sense]
muteaction=0
mute=-1
[hush]
hushpercent=20
[volumecap]
enabled=0
[kenwood]
disabled=0
[ramp]
disabled=1
[menu]
quit=0
sort_playlist=1
[controls]
stalk_side=left
[output]
notify=1
[serial]
car_rate=115200
[tuner]
region=europe
[aux]
source=
title=
artist=Playing CD's
[wendy]
flag_amount=0
[custom]
wendy=
[searches]
amount=0
[VisualFavourites_AM]
count=0
[VisualFavourites_AUX]
count=0
[VisualFavourites_DSP]
count=0
[VisualFavourites_FM]
count=0
[hijack]
dc_servers=1
[shuffle]
deduplicate=1

Anyone?

C.