Follwed the upgrade guide word for word. Everything seems to have gone along properly, but when I try to connect to the player with Emplode it gives the following error and stops:

"Download Failed while Rebuilding Database - Error 0xc0041002"

Here's what my Hyperterminal log looks like during bootup:

hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IC25N080ATMR04-0, 76319MB w/7884kB Cache, CHS=9729/255/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:28:0f:4
b
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 4k initempeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Tried to mount /dev/hdc4 but got error 6
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
player.cpp : 385:empeg-car 2.00-beta13 2002/07/24.
! tags.cpp : 61:Failed to open tags (0xc0041002).
Prolux 4 empeg car - 2.1434 Jul 24 2002
Vcb: 0x4086d000
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IC25N080ATMR04-0, 76319MB w/7884kB Cache, CHS=9729/255/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:28:0f:4
b
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 4k initwarning: can't open /etc/mtab: No such file
or directory
Making first drive...
mke2fs 1.14, 9-Jan-1999 for EXT2 FS 0.5b, 95/08/09
ext2fs_check_if_mount: No such file or directory while determining whether /dev/
hda4 is mounted.
Linux ext2 filesystem format
Filesystem label=
609728 inodes, 78043770 blocks
0 blocks (0.00%) reserved for the super user
First data block=1
Block size=1024 (log=0)
Fragment size=1024 (log=0)
9527 block groups
8192 blocks per group, 8192 fragments per group
64 inodes per group
Superblock backups stored on blocks:
8193, 24577, 40961, 57345, 73729, 204801, 221185, 401409, 663553,
1024001, 1990657, 2809857, 5120001, 5971969, 17915905, 19668993,
25600001, 53747713,

Writing inode tables: done
Writing superblocks and filesystem accounting information:
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IC25N080ATMR04-0, 76319MB w/7884kB Cache, CHS=9729/255/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:28:0f:4
b
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 4k init
empeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Tried to mount /dev/hdc4 but got error 6
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
player.cpp : 385:empeg-car 2.00-beta13 2002/07/24.
! tags.cpp : 61:Failed to open tags (0xc0041002).
Prolux 4 empeg car - 2.1434 Jul 24 2002
Vcb: 0x4086d000

empeg-car bootstrap v1.02 20001106 ([email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!

e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux..................................... done, booting the kerne
l.
Linux version 2.2.14-rmk5-np17-empeg51 (mac@aphex) (gcc version 2.95.3 20010315
(release)) #16 Wed Jul 24 18:19:54 BST 2002
Processor: Intel StrongARM-1100 revision 11
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 9, serial number 40103915)
Command line: mem=16m
Calibrating delay loop... 207.67 BogoMIPS
Memory: 15024k/16M available (964k code, 20k reserved, 372k data, 4k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 206f6972 'rio '
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initialised
empeg audio-in initialised, CS4231A revision a0
empeg remote control/panel button initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0004880).
empeg RDS driver initialised
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hda: IC25N080ATMR04-0, ATA DISK drive
hdb: FUJITSU MHL2300AT, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IC25N080ATMR04-0, 76319MB w/7884kB Cache, CHS=9729/255/63
hdb: FUJITSU MHL2300AT, 28615MB w/2048kB Cache, CHS=58140/16/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:28:0f:4
b
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
hdb: hdb1 < hdb5 hdb6 > hdb2 hdb3 hdb4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 4k initempeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Remounting first music partition read-only
Remounting second music partition read-only
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
player.cpp : 385:empeg-car 2.00-beta13 2002/07/24.
! tags.cpp : 61:Failed to open tags (0xc0041002).
q
rw
rwm
cp -auvfx /drive1/fids /drive0
Prolux 4 empeg car - 2.1434 Jul 24 2002
Vcb: 0x4086d000
ro
Restored terminal settings
Remounting first music partition read-only
Remounting second music partition read-only
Restart code received
Starting player
player.cpp : 385:empeg-car 2.00-beta13 2002/07/24.
! tags.cpp : 61:Failed to open tags (0xc0041002).
rom
logout

empeg-car bootstrap v1.02 20001106 ([email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!

e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux..................................... done, booting the kerne
l.
Linux version 2.2.14-rmk5-np17-empeg51 (mac@aphex) (gcc version 2.95.3 20010315
(release)) #16 Wed Jul 24 18:19:54 BST 2002
Processor: Intel StrongARM-1100 revision 11
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 9, serial number 40103915)
Command line: mem=16m
Calibrating delay loop... 207.67 BogoMIPS
Memory: 15024k/16M available (964k code, 20k reserved, 372k data, 4k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 206f6972 'rio '
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initialised
empeg audio-in initialised, CS4231A revision a0
empeg remote control/panel button initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0004900).
empeg RDS driver initialised
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hdb: FUJITSU MHL2300AT, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hdb: FUJITSU MHL2300AT, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IC25N080ATMR04-0, 76319MB w/7884kB Cache, CHS=9729/255/63
hdb: FUJITSU MHL2300AT, 28615MB w/2048kB Cache, CHS=58140/16/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:28:0f:4
b
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
hdb: hdb1 < hdb5 hdb6 > hdb2 hdb3 hdb4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 4k initempeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Remounting first music partition read-only
Remounting second music partition read-only
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
player.cpp : 385:empeg-car 2.00-beta13 2002/07/24.
! tags.cpp : 61:Failed to open tags (0xc0041002).
Prolux 4 empeg car - 2.1434 Jul 24 2002
Vcb: 0x4086d000

empeg-car bootstrap v1.02 20001106 ([email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!

e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux..................................... done, booting the kerne
l.
Linux version 2.2.14-rmk5-np17-empeg51 (mac@aphex) (gcc version 2.95.3 20010315
(release)) #16 Wed Jul 24 18:19:54 BST 2002
Processor: Intel StrongARM-1100 revision 11
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 9, serial number 40103915)
Command line: mem=16m
Calibrating delay loop... 207.67 BogoMIPS
Memory: 15024k/16M available (964k code, 20k reserved, 372k data, 4k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 206f6972 'rio '
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initialised
empeg audio-in initialised, CS4231A revision a0
empeg remote control/panel button initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0004980).
empeg RDS driver initialised
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IC25N080ATMR04-0, 76319MB w/7884kB Cache, CHS=9729/255/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:28:0f:4
b
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 4k initempeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Tried to mount /dev/hdc4 but got error 6
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
player.cpp : 385:empeg-car 2.00-beta13 2002/07/24.
! tags.cpp : 61:Failed to open tags (0xc0041002).
Prolux 4 empeg car - 2.1434 Jul 24 2002
Vcb: 0x4086d000

Any help would be appreciated.

Okay. The boot logs look a little scrambled, but from what I am guessing:

a) you had a single 30GB drive
b) you are adding an 80GB drive
c) you built the 80GB drive
d) you tried hooking the two drives up and tried to copy the files

At only one point in all of the boot logs do I see a 30GB drive. The rest of it is all 80GB.

With the 30GB disconnected, try syncing one mp3 file to the new 80GB. Verify that works first.

If that works, reconnect the 80 and 30. Boot. Do not use emplode, drop directly to shell. Force everything to read/write and try your copy again. Does that copy work / any errors?

If the copy works, you now have duplicate material on both drives. Again disconnect the 30 and try booting from the 80 only. Check to see that all your music was copied. If that works...

Reconned the 30. Boot, ignoring any errors. In shell, go into the 30 and delete everything from the fids directory. Only do this after testing that everything was copied to the 80 first!!! With the fids directory empty, reboot and resync.

If you tried to put in a second hard disk, it's not finding it.... Were there supposed to be two hard disks?

This was a factory 60gb player, I'm replacing only the second drive with an 80gb drive. I removed both original 30gb drives and put the new 80gb drive in. Ran the builder and then ran 2.0 b13 developer (this is what was on tje player to start with and is still the software on the original 30gb drive0 I plan to put back in). Tried to start the player in Emplode and got this error. re-booted the player a few times and tried again, same thing. Re-installed the builder just in-case and then re-installed 2.0 b13 too. Still the same problem. Then attached the old drive1 and made and attempt to copy the fids from that drive assuming the error had no significance. the copy happend in a blink of an eye. Way to short for nearly 30gb of fids to transfer. I knew that didn't work so I re-booted the player with both drives attached and it started rebuilding database... I went to bed. This morning tried to run Emplode and nothing happened. removed the old drive1 and tried, still nothing. That's when I posted this thread asking for help. I've just tried to upgrade to 2.0 final but for some reason the player still thinks it's b13. Confused.. I am?

here's a less jumbled boot log:

empeg-car bootstrap v1.02 20001106 ([email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!

e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux..................................... done, booting the kerne
l.
Linux version 2.2.14-rmk5-np17-empeg52 (rob@aphex) (gcc version 2.95.3 20010315
(release)) #11 Tue Apr 1 18:49:59 BST 2003
Processor: Intel StrongARM-1100 revision 11
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 9, serial number 40103915)
Command line: mem=16m
Calibrating delay loop... 207.67 BogoMIPS
Memory: 15024k/16M available (964k code, 20k reserved, 372k data, 4k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 206f6972 'rio '
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initialised
empeg audio-in initialised, CS4231A revision a0
empeg remote control/panel button initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0004b80).
empeg RDS driver initialised
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
hda: IC25N080ATMR04-0, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IC25N080ATMR04-0, 76319MB w/7884kB Cache, CHS=9729/255/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:28:0f:4
b
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 4k initempeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Tried to mount /dev/hdc4 but got error 6
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
player.cpp : 385:empeg-car 2.00 2003/04/01.
! tags.cpp : 61:Failed to open tags (0xc0041002).
Prolux 4 empeg car - 2.1434 Mar 26 2003
Vcb: 0x4086d000

Paul, I can't sync one song because I can't start Emplode. It crashes with the 30gb attached or not.

Okay. So you have two original 30s. 30m (master) and 30s (slave). You also have a new 80.

Try this:
Remove all drives.
Install the 80.
Install and run the builder.
Install 2.0b13 (or whatever final version you want)
Verify the 80 by syncing 1 file to it.

If that works:
Install your original 30m as the slave. You will need to change the jumper.
Boot - you will see database errors.
Go to shell.
cd /drive1/fids
ls
You should either see lots of files (pre-fidsift) or a bunch of _directories (post-fidsift)
If you have files (pre-fidsift):
cp /drive1/fids/* /drive0/fids
If you have directories (post-fidsift):
cp -R /drive1/fids/* /drive0/fids
shutdown
Remove 30m and install 30s, being careful about the jumper
Reboot
Resync / rebuild databases & test.

If all went well, your 80 is now master, your original 30s is the slave drive, you should have (nominally) 110GB capacity and all of your files should be there. You also have your old 30m sitting on your desk, for whatever use you choose.

EDIT: Also, be aware of a potential builder bug that has popped up from time to time.

Yeah see, that's the problem. I did remove all the old drives and install just the 80gb. Then I ran the builder and then 2.0b13. It won't allow me to get into emplode to sync anything, it crashes at "Downlaod Failed while Rebuilding Database - Error 0xc41002" and then I have to close Emplode. I also tried to re-install the builder and 2.0b13 just incase the first time it didn't work and got the same thing. that's when I started jacking around with the old drives to see if I could get anything else to happen. Basically, with the new 80gb drive installed, Emplode crashes and I'm done.

See my edit on the previous message. That sounds like the potential builder bug. Try rebuilding the 80, and capture a log of what happens.

Ok, I think my impatience has bitten me once again. I realized by reading pauls post about the "builder bug" that I hadn't really allowed the player to completely reboot and rebuild after applying the disk builder upgrade. So I re-ran the builder and let it completely reboot/rebuild afterwards and ran the stress test for a few minutes. Now all seems to be fine.

However, I do have a quick question. I was interested in making the new 80gb my slave or drive1 and keeping my original 30gb master/drive0 as the master/drive0. Basically to maintain the dynamic data, config.ini, etc... Anyway, going off the Drive Upgrade instructions and the info in Pauls previous 2 posts, I'm going to follow the guidelines for copying the info from one drive to another except I am going to copy the fids from my old slave/drive1 to the new 80gb and then put my original 30gb drive back in as the master and move the 80 to the secondary position with proper jumper and so on. This will accomplish what I want, RIGHT?

Greetings!

Exactly. Because the 80 was built and has the OS on it, it can act as either master or slave. If you:

a) boot with your 80 as master and your original 30s as slave
b) copy the fids from your 30s to the 80
c) reconnect your original 30m as master, 80 as slave
d) reboot, resync

you should get exactly what you want. Better, because your original database files will be intact on the original master drive, and you should not (in theory) even have to rebuild the database. Best to do so anyway, just in case.

Edit: for the sake of sanity, you may want to delete the following files from the 80GB drive. This way, you do not have an old / invalid copy of the database on /drive1...

/drive1/var : config.ini, database, playlists, tags
/drive1/var itself

Good, fids are copying as I type. It'll probably take a while since both original 30gb drives were full to capacity. I've got 3 other players to upgrade after this one, so now they should all go smoothly . Thanks for the help!

And then install 2.00final .

No worries! What are your plans for the old 30GB drives you are removing?

And 2.0 final is a good idea, unless there is something specific that you need from b13 - I think there was a tuner bug of some sort, but I do not remember off hand.

Well, during the whole ordeal this morning, I reattached the original master/slave combo and did the 2.0 final upgrade, so that's done. Then when I rebuilt the new 80gb I put 2.0 on it too. I'm a 2.0 final guy now (looking forward to crossfade).

The extra 30gb drives (3 total) are going into other players:

50gb player (10gb + 40gb) will now be 70gb (30gb + 40gb)
10gb player will now be a 60gb (30 + 30)

This will yeild a nice team of Empegs 2@ 110gb, 1@ 70gb, 1@ 60gb, 1@ 30gb, 1@ 20gb (this one is the wife's)

Hahahahaha! Your wife gets the smallest player!?!? Okay... After seeing all the SWMBO references, I guess it is your life at risk...

As to crossfade, uh, that's actually the 3.0 alphas...

Damn... I was looking forward to crossfade, Oh well.

As far as the wife's Empeg being smallest... I think for her SWMBO should be SWMBTTUTEWGF (She who must be tought to use the Empeg without getting frustrated). I only regret the size of her player when I drive her car and want to hear my own music.

That's..... quite an upgrade farm right there. I always love trickling down hardware to other computers. Out of bean-counting curiousity (no reply necessary, really), what did you have to start with and how did you get to the end point? What a stash of empegs right there!

Believe it or not, there's one more, it's my brothers so I didn't bother mentioning it. It's an orig 30gb and I'm putting an 80gb in it for him and stealing his old 30gb drive for myself

Did you find a decent price on the 80GBs?

I got them for 194.03 @ zipzoomfly.com (used to be googlegear.com), I wouldn't say I stole them, but it wasn't bad.