Hi all, I need a bit of help with this. I switched my drives over from my mk2 to my mk2a and now the player won't boot properly. Thanks for any help!
The display says "initialise mixer failed" and then the player restarts etc, etc, etc... here is the Hyperterminal:
empeg-car bootstrap v1.02 20001106 (
[email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!
e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux.................................... done, booting the kernel
.
Linux version 2.2.14-rmk5-np17-empeg41 (
[email protected]) (gcc versi
on 2.95.2 19991024 (release)) #132 Wed Jan 10 13:49:24 GMT 2001
Processor: Intel StrongARM-11
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 9, serial number 120001067)
Command line: mem=16m
Calibrating delay loop... 207.67 BogoMIPS
Memory: 15048k/16M available (972k code, 20k reserved, 336k data, 8k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 206f6972 'rio '
Logo type is 1
empeg display initialised.
empeg dspaudio driver initialized
empeg audio-in initialised, CS4231A revision a0
empeg infra-red support initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0004780).
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel I
Probing primary interface...
hda: IBM-DARA-212000, ATA DISK drive
hdb: IBM-DJSA-220, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IBM-DARA-212000, 11513MB w/418kB Cache, CHS=23392/16/63
hdb: IBM-DJSA-220, 19077MB w/1874kB Cache, CHS=38760/16/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman (
[email protected])
SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:18:04:2
b
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
hdb: hdb1 < hdb5 hdb6 > hdb2 hdb3 hdb4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 8k init player.cpp : 385:empeg-car 2.00 20
03/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-pla
Starting bash.
úShell exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
Starting bash.
úShell exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
l exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
Starting bash.
úShell exit
player.cpp : 385:e
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
Starting bash.
úShell exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-playe
Starting bash.
úShell exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
Starting bash.
no shell!
Shell exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
Starting bash.
úShell exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
exit
player.cpp : 385:empeg-car 2.00 2003/04/01.
! player.cpp : 291:MainThread::Init failed!
Switching to shell-player loop
Starting bash.
úShell exit
etc....etc...etc...
Previous Topic
Index