My empeg locked up this morning on a song at the very begining and now it wont respond after boot strap.
I ran Hyper term - it appears everything loads up fine...
starts player and hangs right there. I reloaded 1.03 successfully and no luck.
I then ran the Diag "CTRL-T" from hyperterm....
All passed ok.
I checked the suspect original song on my PC and it is ok.
i suppose it's possible that this song is corrupt on my player and causing the lockup?
The question is how do i find this bad tune to delete it?? .... or change the player so it does not try to keep playing the same song at bootup as to avoid the lockup and use emplode to remove it?

My Log...........
_________________________________________________
ÿIf there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!

e000 v1.03
Copying kernel...
Calling linux kernel...
Uncompressing Linux................................... done, booting the kernel.

Linux version 2.2.14-rmk5-np17-empeg43 ([email protected]) (gcc versi
on 2.95.2 19991024 (release)) #213 Sat Jun 23 16:35:13 BST 2001
Processor: Intel StrongARM-1100 revision 11
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 7, serial number 80000516)
Command line: mem=12m temp=37
Calibrating delay loop... 207.67 BogoMIPS
Memory: 11008k/12M available (960k code, 20k reserved, 292k data, 8k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 67706d65 'empg'
Scheduling custom logo.
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initialised
empeg audio-in initialised, CS4231A revision a0
empeg remote control/panel button initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0004600).
empeg RDS driver initialised
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hda: IBM-DARA-212000, ATA DISK drive
hda: IBM-DARA-212000, ATA DISK drive
hda: IBM-DARA-212000, ATA DISK drive
hda: IBM-DARA-212000, ATA DISK drive
hda: IBM-DARA-212000, ATA DISK drive
hda: IBM-DARA-212000, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IBM-DARA-212000, 11513MB w/418kB Cache, CHS=23392/16/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:10:02:0
4
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...okay
Freeing unused kernel memory: 8k initI see this is a developer image!
Mounting proc
Mounting first music partition
Mounting second music partition
Tried to mount /dev/hdc4 but got error 6
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To ComðStarting
player
empeg-car 1.03.
________________________________________________
After about 1 miniute or two it drops to the bash prompt
resume log........
________________________________________________
Restored terminal settings
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Player exited normally: 1
Switching to shell-player loop
Starting bash.
empeg:/empeg/bin#
__________________________________END LOG________
Anyone have any Ideas????
Thanks!!

12Gb MKII 080000516 Blue

Looks like the same problem I had a while back, even though the song that it seemed to lock up on was fine. Try the fix Hugo suggests here

Awesome!!!
That did the trick!!!!
I read your reply post and I had exactly the same issues as you except it appears my song is corrupt.
This board continues to amaze me with all of the awesome people here that keep this community going.
I just hope it stays even after SB has forgotten about the Empeg.
Thanks again Drakino!!

12Gb MKII 080000516 Blue

Interesting note....
When I went to delete the offending song, Empeg reported deleting a different song, and then promptly failed the sync process.
I went back in and deleted the cross reference song and all is well.
guess they got corrupt aginst the files table or Database??
The Error was:
The synchronisation process failed during stage 10:
Operation not permitted error 0xffffffff

12Gb MKII 080000516 Blue